Pengaruh Kombinasi Pemangkasan Ujung Magnet Permanen dan Axial Channel pada inti rotor terhadap Torka Cogging pada Generator Tipe Fractional Slot Number

Authors

  • Yudha Suherman
  • Tajuddin Nur

DOI:

https://doi.org/10.25170/jurnalelektro.v13i2.1973

Keywords:

magnetic tip trim, axial channel, permanent magnet synchronous generator, cogging torque

Abstract

This paper is about to discuss the effect of combining a magnetic shaping technique with an axial channel in the rotor core to reduce the cogging torque of a permanent magnet synchronous generator. Computation process is performed by using the optimization response surface method. In this case, this research is done by employing two types of axial channel systems, namely circular and hexagonal. The axial channel area at the core of the engine rotor is 0.000279683 m2. Determination of magnetic shaping was carried out with an angle of 10 and a surface angle of 530. The effect of the combination of the cogging torque reduction technique with magnetic shaping and axal channel was analyzed by numerical method based on the finite element method (FEMM). Based on the analysis, it is found that the combination shows a decrease in cogging torque by 98% when compared with the cogging torque in the initial design (initial structure). Another advantage of the combination of the two cogging torque reduction techniques is that there is no significant increase in the magnetic flux density of the engine core. It can be said that the combination of the cogging torque reduction technique and the axial channel at the core of the engine rotor can significantly reduce the cogging torque.

References

[1] Ali, Mohd Hasan. 2012. Wind Energy Systems. Taylor & Francis Group.
[2] Bargallo, Ramón. 2006. Finite Elements for Electrical Engineering. Electrical Engineering Department. Universitas Politécnica De Catalunya. Barcelona.
[3] Binder Andreas. Cogging Torque Reduction for Interior Permanent Magnet Synchronous Motor, 2016.
[4] Candel, Miquel Tost. 2016. “Cogging Torque Reduction for Interior Permanent Magnet Synchronous Motors”. Department of Electrical Engineering and Information Technology. Technical University of Darmstadt. Darmstadt.
[5] D.Hanselmann. Brushless Permanent Magnet Motor Design: Magna Physics Publishing Motorsoft Division of Fisher Electric Technology, Magna Physics Publishing, 2006.
[6] https://www.academia.edu/. Generator Sinkron 3 Fasa.
(https://www.academia.edu/4773352/BAB_II_GENERATOR_SINKRON_TIGA_FASA_dimana_f_Frekuensi_listrik_Hz, diakses 20 Oktober 2019).
[7] https://blogs.itb.ac.id. Synchronous motor & generator.
(https://blogs.itb.ac.id/el2244k0112211083igustiagunggede/2013/04/29/synchronous-motor-generator/, diakses 19 November 2019).
[8] Hsio. Chun Yu, dkk. 2011. A Novel Cogging Torque Simulation Method for Permanent-Magnet Synchronous Machines.
[9] Hendershot Jr, J.R dan TJE Miller. 1994. Design of Brushless Permanent-Magnet Motors. Magna Physics Publishing. Hillsboro. OH 45133.
[10] https://kumparan.com/. Potensi Energi Terbarukan di Indonesia.
(https://kumparan.com/kajian-patra/ada-apa-dengan-energi-hijau-di-indonesia. diakses 20 Oktober 2019).
[11] http://repository.lapan.go.id/. 2007. Analisa Potensi Energi Angin dan Estimasi Energi Output Turbin Angin di Lebak Banten.
(http://repository.lapan.go.id/index.php?p=show_detail&id=1565, diakses 20 Oktober 2019).
[12] Jeeng-Min Ling dan Tajuddin Nur. 2012. Study of Magnetics Performance of Inset Permanent Magnet Synchronous Machine (Inset - PMSM) using Finite Element Method. Department of Electrical Engineering, Southern Taiwan University of Science and Technology. Taiwan. Applied Mechanics and Materials Vols 260-261 (2013) pp 554-558.
[13] Jeeng-Min Ling dan Tajuddin Nur. 2016. Influence of edge slotting of magnet pole with fixed slot opening width on the cogging torque in inset permanent magnet synchronous machine. Department of Electrical Engineering, Southern Taiwan University of Science and Technology. Advances in Mechanical Engineering 2016, Vol. 8(8) 1–9.
[14] Liwei Song, dkk. 2010. Reluctance Torque Analysis and Reactance Calculation of IPM for HEVs Based on FEM.
[15] Marappung, Muslimin. 1979. Teknik Tenaga Listrik. Bandung: Armico.
[16] Myers, Raymond H. 2016. Response surface methodology: process and product optimization using designed experiments 4th ed. John Wiley & Sons, Inc. Hoboken. New Jersey
[17] Nur.Tajuddin, dan Herlina. 2018. Enhancement of Cogging Torque Reduction on Inset Permanent Magnet Generator by Using Magnet Edge Shaping Method, International Conference on Electrical Engineering and Computer Science.
[18] Nur.Tajuddin, dan Liza Evelyn Joe. Study the Effect of Height and Lenght of Slotting in Magnet Edge on The Cogging Torque Reduction of Franctional Slot Number in Magnet Permanent Machine, In : International Conference on Electrical Engineering, Science and Technology (ICEST), 2029, Bandar Lampung.
[19] Nur.Tajuddin, dan Sri Mawar. 2019. Study the Influence of Edge Points of Magnet Surface and Stator Core on the Cogging Torque Reduction in Permanent Magnet Machine, In : International Conference on Electrical Engineering, Science and Technology (ICEST), 2019

Downloads

Published

2021-02-17
Abstract views: 290 | PDF downloads: 255